How is lathe used? What is operation method?

  • Time:
  • Click:118
  • source:KOMANG CNC Machining
Always can hear lathe of the respecting when others is chatting, so after all what is lathe? Is it how will operate? Look please next this small the introduction that write. Explanation: Lathe is to basically use the machine tool that lathe tool has turning is machined to gyral workpiece. Usable still on lathe broach, reamer, reamer, tap, front tooth and tool rolling a flower have corresponding treatment, in and other places of our country Hong Kong also someone cries lathe. Lathe weighs a machine tool again, the worker of use lathe is called " lathe work " , the job that is considered as all equipment in the lathe in machining industry " master " . Lathe basically is used at processing a rod, dish, cover and other the work that has hodometer side, give priority to with cylinder, it is mechanical make and a kind of the widest machine tool is used in factory of make repairs and supply replacements. Milling machine and drilling machine rotate the machinery of treatment comes out from lathe amplify. How is lathe used? What is operation method? Operation method 　 1, before lathe switchs on the mobile phone, it is normal to check oil path and rotational part above all, tight coverall should be worn when switching on the mobile phone, cuff clasp, long hair should take helmet, prohibit wearing a glove, cutting workpiece and glasses must be worn when grinding a knife. 2, it is normal that when switching on the mobile phone, equipment should watch, lathe tool wants clip to originally, deepness of penetration of a cutting tool cannot exceed the load of equipment itself, 1 what knife head extends a part not to exceed cutter hub height.

5 times, a bolo wants to quit the position that returns safety when rotational tool carrier, prevent lathe tool to touch Chong chuck, great work falls on, board should be filled up on bed face. Cooperate to assemble and unassemble with crane when workpiece, clip dish not clamp workpiece does not allow debus spreader, and want disconnect the full control power source of crane. Before the lathe after workpiece clamp is rotational, debus of beard general spreader. 3, when use emery cloth grinds workpiece, emery cloth wants to be filled up with hardwood, lathe tool should move to forbid to set tool and part to face of safe place, tool carrier, delimit needle dish should put prison. 4, it is rear and OK that lathe alternates rotate speed should stop lathe to turn changeover, lest touch gear, when driving, lathe tool should approach work slowly, lest bits foam collapse hurts person or attaint work. 5, lathe working hours cannot leave working post at will, prohibit fun fights noisely, occupied leave must stop phone of act on one's own judgment in an emergency, the thought when the job wants to center, workpiece cannot be measured in machine movement, garment newspaper cannot change near the lathe in movement, the personnel that fails to obtain mount guard evidence cannot operate lathe alone. 2.

1 chuck and flange of main shaft join dish: Match 3 claw and F200 of 4 ungual chuck, F250, F320, F400, F500, F800; Different type place matchs flange dish different 　 2.

2 calories of claw: Outfit go up in chuck, belong to fragile, different chuck type matchs different card claw; To 3 ungual chuck, its block ungual branch ungual (end panel takes a tooth-like part of anything) , turn over claw (end panel does not take a tooth-like part of anything) , the activity is ungual (take bolt, but positive and negative is amphibious) 3 kinds. Because produce manufacturer to differ, the ply blocking claw that place of same norms chuck matchs and flank chamfer are wide different also, for instance: To K11160 cent blocking claw plants: Huhhot is produced for 19 × 10 (Mm) (ply X chamfer is wide) , tile-roofed house inn is produced for chamfer of X of ply of 10(of 20 × wide) , Shanghai is produced for 19 × 7(ply × chamfer is wide) , Yantai and produce without stannum it is 18 × 10(ply. To K11200 cent blocking claw plants: Huhhot is produced for chamfer of × of ply of 22 × 10(wide) , tile-roofed house inn and Yantai are produced for 10(of 20 × ply × chamfer is wide) , Shanghai is produced for 25 chamfer of × of × 10(ply is wide) . Block claw to K11250 each manufacturer size is same. The activity is ungual (take bolt, but positive and negative is amphibious) 250 chuck claw has a kind, 320 (325, 380) chuck claw has 9 tooth and 10 teeth two kinds, ply has 34 mix two kinds 36; Ungual to 4 ungual chuck, cent K72320, K72400, K72500, K72630, K72800 　 among them does K72500 block ungual branch 42, 45, how is lathe of 3 kinds of 48 ply used? What is operation method? 2.

3.

Chuck bevel gear, use on 3 ungual chuck, the sort that offer money has 160, 200, 250, 320, 380, 400 wait for chuck to use bevel gear. 2.

4.

Chuck dish silk: Use on 3 ungual chuck, with clench the teeth of chuck bevel gear, drive movement blocking claw. The sort that offer money has 160, 200, 250, 320 wait for chuck to use dish of silk. 2.

5 chuck guide screw: Use on 4 ungual chuck, with clench the teeth blocking claw, drive movement blocking claw. Sort of chuck guide screw is more, the circle outside pressing guide screw and length offer money: The circle outside expressing methodological T() × L (length) , t22 × 70, T26 × 85, T28 × 105, T32 × 110, T32 × 118, T32 × 125, T32 × 131, T32 × 136, T32 × 151, T35 × 180, T35 × 165, T36 × 170, 180 　 of T36 × 　 2.

6.

Card column: Outfit it is among chuck guide screw, according to the diameter that blocks column and upside semicircle ply cent is the following kinds: 24 × of Φ 13, 28 × of Φ 16, 30 × of Φ 14, 30 × of Φ 18, 32 × of Φ 16, 32 × of Φ 18, 32 × of Φ 20, 35 × of Φ 18, 36 × of Φ 18, Φ 40 wait. CNC Milling CNC Machining